This blog will document the restoration of Cape Dory Typhoon (Weekender) Hull #1044. The Cape Dory Typhoon is a great sailing small-scale 'yacht', and offers a very friendly experience for her captain and crew. The scope of this restoration project will be painting the interior, deck and topsides, as well as fabricating new teak brightwork.

Friday, October 20, 2017

Port Cockpit Locker Hatch

October 20, 2017


Home from a business trip, I decided to close out the Friday afternoon with laying up the port cockpit seat locker hatch.  As I had done with the starboard hatch (barely visible in the background), I prepared the template / mold by covering it with plastic film.  I then prepared the fiberglass: 11' of 6" 1708 biaxial tape and 3' of the 4" 1708 tape.  The glass was cut and the work surfaces set up so I moved forward with mixing epoxy.  Like I had done with the starboard side, I fully wet out two 6" pieces of glass, applied them to the mold, and then covered the seam with a 4" piece.



I progressed through another 4 pieces of 6" 1708 biaxial tape, or two layers, for a total of 3 layers of 1708 biaxial.  I will allow this to cure before coming back to water-wash, sand and prepare the surface for another couple layers of glass.  The 5 layers of glass will be further strengthened by supports that I will glass-in on the underbellies of each hatch.



Total Time Today: 1.75 hrs

Tuesday, October 17, 2017

Starboard Cockpit Locker Hatch

October 16, 2017


After my day job I decided to get some time in on the cockpit locker hatches, and to begin with I testing a scrap piece of foam on the router table.  Using the 1/2" radius bit, I ran the scrap piece along the fence to apply the desired cut.



The results were just what I was looking for on the eventual finished locker hatch.  With that successful test, I then turned to the templates for the same application.



After running all four sides of the tops of each template / mold across the router table's 1/2" radius bit I noticed that the alignment of the bit was not strictly perfect - leaving a bit of a hard transition line from the top to the radius surface, as can be seen in the picture below.  



I "softened" the transition line from top to side with the use of some very fine grit sandpaper that I had on hand.  The necessity of having a fair curve in the transition was not too important, but I did want to create a nice transition for the heavier fiberglass cloth to assume.  In addition, if there was any strange result in the layup, I would address with fairing compounds on what would be the underside of the hatch itself.  



With the top-to-side radius applied to all sides of both hatches, and with the smoothing completed with the fine grit sandpaper, I wrapped the starboard locker hatch with plastic and then hot-glued the template to a large would block.




I had laid a sheet of plastic down on my fiberglass wet-out board; on one end I had the template staged for work, and on the other end I would wet-out the fiberglass itself.  The picture below shows two lengths of 6" 1708 biaxial tape in a butt joint along the length of the template, with a length of 4" 1708 biaxial tape overlapping and also running the length of the template.



A close-up picture of the first layers of cloth applied.



Ultimately, I would finish the short work session with laying down 6 lengths of the 6" 1708 tape and the 1 length of 4" 1708 tape.  I essentially had 3 layers of 1708 glass on the template.  Since the work surface was generating a bit of heat as a result of the curing process, I decided to draw things to a close for the day.  I plan to water-wash the surface, sand to abrade the surface for a good mechanical bond, and then lay up an additional layer of 1708 and then finish with a lighter cloth prior to fairing the surface for primer and paint.  The material hanging below the template will be cut to create a finished bottom edge.



Total Time Today: 2.5 hrs

Saturday, October 14, 2017

Continued Surface Prep (Fill & Fair) and Creating Cockpit Seat Hatch Molds

October 14, 2017


I got to unpacking some recent arrivals to the shop - preparing for interior paint, including the bilge.  In addition to the paints that arrived, I also received some 1708 biaxial and some Divinycell for the cabin sole recore work to be completed.  Setting these items aside, I got to work on Joule by beginning with the usual water-washing of the previous fairing application.



After washing off the cure amine blush, I turned to addressing the imperfections across the surfaces of the cabin top and sides.  I dished out crack and gouges using a spiral saw, and then vacuumed up the debris. 



I solvent-washed all worked areas as preparation for an application of fairing compound (epoxy thickened with 406 silica and 407 low-density).



With the worked areas cleaned of contaminates, I applied a film of 'neat' epoxy - not thickened with any filler compounds - and then proceeded to mix another batch of epoxy this time thickened with the aforementioned recipe of thickening agents.  Since this mixture sands relatively easily, I went ahead and "slathered" on more material than I should in hopes of limiting myself to one application of filler, and two at the most.



I also skimmed a coat of fairing compound on the nearly complete poop deck and counter.



Next, I turned my attention to fabricating cockpit seat locker hatches - at least giving it a go!  Using the hot glue gun and scrap materials from the shop, I marked out what would become the interior dimension of the port and starboard cockpit locker hatches.



With both templates built, I removed them from the Joule and continued working them in the shop.



I used a 3/4" sheet of polystyrene to prepare the molds, for which fiberglass will be laid.  I cut out two pieces each for the port hatch and the starboard hatch, in oversized dimensions.  I then glued up the two pieces, creating a 1.5" thick mold.  Next, I scribed the lines of the templates onto the mold material, and then cut out the mold to match the dimensions of the port and starboard templates.



In a future work session, I will radius the top of the molds on all sides to prepare them to accept the fiberglass.  Once the glass is applied - probably 3 to 4 layers of 1708 biaxial - I will remove it from the mold and glass in support material on the underside of each hatch.   I expect the exercise in fabricating the hatches will run 6 to 8 hours of work with limited materials required.




Total Time Today: 3.75 hrs